How do you replace the pull cord on a Stihl FS 56 RC?

When replacing the pull cord on a Stihl FS 56 RC, it’s important to remember that this is not just like any other lawnmower. The safety tips and instructions for use are different from what you’re probably used to – so make sure you take your time!

The “stihl fs 56 rc recoil starter assembly” is the part that you will need to replace in order to fix your “How do you replace the pull cord on a Stihl FS 56 RC?”. The process of replacing this part is easy and can be done with just a screwdriver.

How to Replace a Trimmer’s Pull Cord

Remove the last piece of the cover.
Remove the snap ring from the ring.
The unit should be disassembled into two sections.
The coil must be removed from the shaft.
After removing the coil, keep the spring in place.
Remove the rope that has broken.
Remove any debris from the lid.
Make a fresh piece of rope by measuring it out.

As a result, you may wonder how to replace the pull cord on a Ryobi trimmer.

How to Replace the Ryobi Trimmer’s Starter Rope

[top] REMOVING THE STARTER ROPE 1. Take off the back cover.
Remove the carburetor from the system.
Disconnect the engine from the clutch housing and upper shaft.
Glue the piston together.
Remove the clutch drum from the assembly.
Remove the clutch from the system.
Remove the starting component from the machine.
Take off the starting handle.

On a Craftsman weedeater, how do you change the draw cord? To examine the spring and pulley system, turn the starter assembly over. Remove the pulley from the spring while holding it in place. With the starting rope linked to the spring, lift the pulley. The rope should be unwound, cut from the pulley, and discarded.

In turn, how can I repair my Troy Bilt pull cord?

On a Troy-Bilt pull start engine, how do you change the rope?

To prevent your Troy-Bilt tool from accidently starting while you’re working on its inner components, disconnect the spark plugs.
Remove the tool’s engine compartment’s exterior cover.
Make a note of where the pull string is put and in which direction it is placed.
Remove the pulley and the old rope from the pulley.

On a Stihl FS 56, how do you remove the head?

In the hole on the left at the rear of the gear head, insert the provided pin or screwdriver. The output shaft is accessed by this hole. To block the shaft, push the pin in as far as it will go. Unscrew the trimmer head from the shaft by twisting it clockwise.

Answers to Related Questions

On a Stihl FS 55, how do you replace the line?

Accessing the spool within the Autocut trimmer head is the first step in loading fresh line into the trimmer head.

Make sure the Stihl FS 55 trimmer is on a flat surface.
With one hand, hold the trimmer head’s body.
Pull the spool straight off the trimmer head by pressing down on it and rotating it slightly to the left.

What’s the best way to restring a Stihl FS 55 Weedeater?

Stihl FS 55 RC Trimmer String Replacement

Remove the power supply.
Replace the monofilament line with two 6-foot lengths of 0.095-inch monofilament.
Rewind the second length of line around the opposite compartment of the inner spool and repeat the operation.
In the power head, place the refilled inner spool.

What is the line size used by a Stihl FS 56?

FS 56 RC-E string trimmer by Stihl. This gasoline-powered string trimmer from Stihl features a straight shaft and weighs 12.5 pounds. Dual. 095-inch cutting lines are used.

What is Stihl Easy2Start and how does it work?

The even pull on the starting rope overcomes the compression of the engine, requiring less strength and effort to start. The STIHL Easy2StartTM helps draw the starter rope smoothly and evenly all the way out, unlike the traditional starting method, which needs fast or uneven motions to activate.

What’s the best way to repair a recoil starter?

If you unintentionally let off of the recoil starter while it is tensioned, a little tab on the pulley might slash your hand.

Remove the cap from the recoil housing. Remove the cap that secures the pulley to the recoil starter housing by unscrewing it.
Take the rope and untangle it.
The spring should be re-tensioned.
Put the cap on.
Replace the rope.
Make a coil using the cord.

What is a pull start and how does it work?

The rope’s handle or grip is pulled by the operator. This causes the rope to unravel and revolve around the crankshaft. The engine is cranked by the crankshaft turning. The action of the crankshaft contacts the flywheel, allowing the engine to start.